Mitsubishi Outlander PHEV

From BITPlan can4eve Wiki
Revision as of 07:16, 18 July 2017 by Wf (talk | contribs)
Jump to navigation Jump to search

ODII PIDs

Potential PIDs:

  1. PHV Battery Power
  2. Gas Engine Power
  3. MG1 Power
  4. MG2 Power
  5. Regen Cooperation
  6. Fuel Input
  7. Distance Since Oil Change for U.S.A. (reset)
  8. Room Temp
  9. Vehicle Load
  10. Mass Air Flow
  11. Manifold Air Pressure
  12. Intake air temperature
  13. Coolant temperature
  14. Engine Speed
  15. Vehicle Speed
  16. Engine Run Time
  17. Injection volume (Cylinder 1) for 10 times
  18. Injection duration for cylinder 1
  19. Actual Engine Torque
  20. State of Charge
  21. Calculated Load
  22. Ambient Temperature
  23. Atmosphere pressure
  24. DTC Clear Warm Up
  25. DTC Clear Run Distance
  26. DTC Clear Min
  27. +B
  28. State of Charge (All Bat)
  29. Shift Sensor Main
  30. Shift Sensor Sub
  31. Shift Sensor Select Main
  32. Shift Sensor Select Sub
  33. Auxiliary Battery Temperature
  34. Engine Rev (Sensor)
  35. MG1 temperature
  36. MG1 temperature after IG-ON
  37. MG1 temperature Max
  38. MG1 revolution
  39. MG2 temperature
  40. MG2 temperature after IG-ON
  41. MG2 temperature Max
  42. MG2 revolution
  43. MG1 torque
  44. MG1 torque execution value
  45. MG1 Control Mode
  46. MG2 torque
  47. MG2 torque execution value
  48. MG2 Control Mode
  49. Inverter MG1 Temp
  50. Inverter MG1 Temp after IG-ON
  51. Inverter MG1 Temp Max
  52. MG1 Gate Status
  53. Inverter MG2 Temp
  54. Inverter MG2 Temp after IG-ON
  55. Inverter MG2 Temp Max
  56. MG2 Gate Status
  57. Boost converter temperature (upper)
  58. Boost converter temperature (lower)
  59. Boost converter temperature after IG-ON
  60. Boost converter temperature Max
  61. Converter Gate Status
  62. Overvoltage Input to Converter
  63. Overvoltage Input to Inverter
  64. VL-Voltage before Boosting
  65. VH-Voltage after Boosting
  66. Prohibit DC/DC converter signal
  67. Aircon Gate Status
  68. Water Pump Running
  69. Inverter Water Pump Revolution
  70. Inverter Coolant Temp
  71. MG1 Inverter Shutdown
  72. MG1 Inverter Fail
  73. MG2 Inverter Shutdown
  74. MG2 Inverter Fail
  75. DCDC Cnv Target Pulse Duty
  76. Water Pump Run Control Duty
  77. Converter Shutdown
  78. Converter Fail
  79. MG1 Carrier Frequency
  80. MG2 Carrier Frequency
  81. Boost Ratio
  82. Converter Carrier Frequency
  83. A/C consumption power
  84. Battery Block Voltage -V01
  85. Battery Block Voltage -V02
  86. Battery Block Voltage -V03
  87. Battery Block Voltage -V04
  88. Battery Block Voltage -V05
  89. Battery Block Voltage -V06
  90. Battery Block Voltage -V07
  91. Battery Block Voltage -V08
  92. Battery Block Voltage -V09
  93. Battery Block Voltage -V10
  94. Battery Block Voltage -V11
  95. Battery Block Voltage -V12
  96. Battery Block Voltage -V13
  97. Battery Block Voltage -V14
  98. Auxiliary Battery Voltage
  99. Power Resource VB
  100. VMF Fan Motor Voltage1
  101. HV battery intake air temperature
  102. Temp of Batt TB1
  103. Temp of Batt TB2
  104. Temp of Batt TB3
  105. Battery pack current
  106. Cooling Fan 0
  107. Cooling Fan Relay Status
  108. Battery block minimum voltage
  109. Battery block number with minimum voltage
  110. Battery block maximum voltage
  111. Battery block number with maximum voltage
  112. Difference between maximum & minimum voltage
  113. Number of battery blocks
  114. Accumulated Time of Battery Low
  115. Accumulated Time of DC Inhibit
  116. Accumulated Time of Battery too High
  117. Accumulated Time of Hot Temperature
  118. Internal Resistance R01
  119. Internal Resistance R02
  120. Internal Resistance R03
  121. Internal Resistance R04
  122. Internal Resistance R05
  123. Internal Resistance R06
  124. Internal Resistance R07
  125. Internal Resistance R08
  126. Internal Resistance R09
  127. Internal Resistance R10
  128. Internal Resistance R11
  129. Internal Resistance R12
  130. Internal Resistance R13
  131. Internal Resistance R14
  132. Power Resource IB
  133. HV battery discharge control
  134. HV battery charge control
  135. Delta SOC
  136. SOC after IG-ON
  137. SOC Max
  138. SOC Min
  139. ECU Control Mode
  140. Battery Cooling Fan Mode
  141. Standby Blower Request Status
  142. Short Circuit Wave Highest Value
  143. Model Code
  144. Engine Code
  145. Destination
  146. ECU Code
  147. Number of Current Code
  148. Number of History Code
  149. Seat Belt Beep Query
  150. Seat Belt Beep Disable All
  151. Seat Belt Beep Disable Driver Only
  152. Seat Belt Beep Disable Passenger Only
  153. Seat Belt Beep Disable Rear Only
  154. Seat Belt Beep Enable All
  155. Seat Belt Beep Enable Driver Only
  156. Seat Belt Beep Enable Passenger Only
  157. Seat Belt Beep Enable Rear Only
  158. Reverse Beep Query
  159. Reverse Beep Disable
  160. Reverse Beep Enable
  161. Disable Traction Control
  162. Set Battery Cooling Fan Speed 0 (Off)
  163. Set Battery Cooling Fan Speed 1
  164. Set Battery Cooling Fan Speed 2
  165. Set Battery Cooling Fan Speed 3
  166. Set Battery Cooling Fan Speed 4
  167. Set Battery Cooling Fan Speed 5
  168. Set Battery Cooling Fan Speed 6 (max.)
Retrieved from "http://can4eve.bitplan.com/index.php?title=Mitsubishi_Outlander_PHEV&oldid=702"